What is progressive overload and how do I use it to build muscle
Progressive overload is the process of increasing the stimulus placed upon a certain muscle or exercise over time
The main ways to produce progressive overload are:
Muscle action
Loading and volume
Exercise selection and order
Rest periods
Repetition velocity
Frequency
While there are all these options, trying to implement all of them often causes confusion, overwhelm, and slow progression
So lets simplify things a bit
Muscle action
Muscle action is not always easy to measure and unless you have a strong knowledge base of anatomy, physiology and biomechanics it can be easy to get lost in the technical jargon and theories. Other factors that come into muscle action as well are the measured muscle activity, level and type of muscle fibre recruitment, torque placed through the pivot points, the length of the moment arm, and the points of insertion and attachment of the muscles. See what I mean technical jargon that won’t make sense to most people. These factors can also be difficult to measure and are not easily influenced. Especially the insertion and attachment points of our muscles.
For now let’s eliminate that factor
Loading and volume
This is in my opinion (and most research will back me up) the best and simplest form of progressive overload to influence. Put simply this is mainly influenced by increasing either the amount of weight you lift or the amount of repetitions/sets you perform. The simplest version of volume can be calculated with the following equation “weight x reps x sets”. While this equation does have its faults in that it doesn’t factor in many of the factors that I spoke about in the muscle action section, it is simple and relatively accurate. With loading and volume, you will respond best by finding the lowest volume that you respond to and then increasing it very slowly overtime with scheduled deload periods. I will keep it as that for now because I want to keep things simple and loading/volume really needs an article of its own to go into the required detail
That’s a tick then for tracking loading and volume
Exercise selection and order
This has a major impact on your loading and volume which makes it another important factor in progressive overload. For example, the training volume for an exercise such as the dumbbell fly will be much lower than that of a bench press if reps and sets are matched. Note that this isn’t factoring in the variables in the muscle action section. The important thing to note from this section is that you do not need to keep switching your exercises constantly in an attempt to “shock your muscles” Muscle don’t get shocked; they adapt and grow based on an increased demand placed upon them. Stick with mostly compound exercises, find the one’s that you like or you know produce great results based on prior learning such as the squat, bench press and deadlift, and increase the loading and volume with these exercises over time
Another tick there
Rest Periods
I’m a firm believer that you should rest as long as you need to and not rush the exercise. If you rush through the exercise and start the next set before you allow for adequate recovery you sacrifice the amount of weight you would have been able to lift or the amount of reps you could’ve performed, thus negatively influencing volume. Rest as long as you need to and allow for adequate recovery time so you can focus on lifting your target weight rather than focusing on trying to catch your breath back. If you are strapped for time, superset opposing muscle groups. This way one group of muscles have time to recover while you are using the opposing group, e.g. Chest with back. In addition to this I have found no reliable research to support a positive correlation between decreased rest time and increased muscular hypertrophy or strength
That’s a big no for decreasing rest time, however, I would say that it can indirectly impact on progressive overload if you haven’t been taking enough rest time and now thanks to this article you change your ways
Repetition velocity
I personally am not a fan of time-under-tension (TUT) training. I believe that while it may increase the total load placed on the muscle, you have to sacrifice weight to achieve this technique therefore rendering the desired result mute. For example, let’s say that you are performing a bench press; 10 reps, 60kgs, with a movement velocity of 1 second concentric (pushing phase), 2 second eccentric (lowering phase.
Using a basic equation of reps x weight x time under tension (10 x 60 x 3) = 1800
Then comparing to a TUT movement of 10 reps, 30kgs (you would have to lower the weight to achieve the slower movement), 2 seconds concentric, 4 seconds eccentric.
Using the same equation, we would get 10 x 30 x 6 = 1800
Now, while this is an exaggerated example. The principle remains. I still believe that you would achieve better results and better progressive overload by keeping a steady movement velocity and focusing on increasing basic training load and volume i.e. weight lifted, or number of reps and sets performed
On that basis I’m going to count this one out as well.
Frequency
One of my favourites and one that I believe has the largest influence on progressive overload and adaptation if used correctly and at the right point in your training career. As this too can be quite a lengthy topic, I’ll try to restrain myself again and not go too in depth. Basically, the influencing factor here is increasing the amount of times throughout a week that you train a certain muscle group. As you train a certain muscle, the fibers within this muscle develop micro tears. These micro tears must be repaired over the next few days through adequate nutrition and rest. The muscle adapts to the initial training stimulus from that first training session and grows stronger in order to be able to better handle that same stimulus. This adaptation process usually occurs between about 2-4 days of that session and is known as the supercompensation period. The idea behind increasing your frequency is to train this muscle at the height of the supercompensation period, cause more microtears and have the muscle adapt again causing a higher peak during the next supercompensation period. You can see graphs of this process below
However, using frequency manipulation for progressive overload has its limitations with the main one being that you can only increase it a certain number of times. I would not suggest having a frequency any greater than 3 times a week for any given muscle.
So, there you have it. Out of these 3 factors of progressive overload I would only really recommend implementing 3 of them. To make things even easier for you guys I will even rank these 3 with 1 being the best:
Loading and volume
Exercise selection and order
Frequency
Train smart, train consistently and train hard
Author,
Jayden Damrow, aka The Hardgainer Trainer



Comments